View ID1A-6S-254SF21_1253531.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

SIM Card Sockets
ID1A Series
Miniature and Thin
Plecement surface
17 .4
30. 6
2.45
Photograph (1)
sFeatures
1. Suited for Plug-in SIM Cards of the GSM Standard (11.11)
In Europe, SIM card Subscriber Identity Modules are used for subscriber identification with portable telephone terminals of the GSM system for which standards have been unified. The ID1A Series of sockets are suited for use with GSM standard (11.11) plug-in SIM cards.
Slide Lock System
LOCK OPEN
Can be locked by moving the slider.
2. Miniature and Thin
These sockets are miniature and thin with a height of 2.45 mm, length of 30.6 mm, and width of 17.4 mm. The weight has been reduced by 30% compared with our existing products. (See Photograph (1).)
Upside down insertion of the SIM card is prevented through the establishment of a polarity.
3. Suited to Automatic Mounting
The board mounting method is of the surface mount type.In addition to the standard tray packaging specification, an embossed tape specification suited to automatic mounting is also available.
Photograph (2)
Structure and Names of the Parts
Slider Card holder
4. Prevention of Incorrect Insertion to the Board
A board-positioning boss prevents incorrect insertion to the board by means of boss position and boss diameter.
5. Slide Lock System
An original lock structure securely holds the SIM card and easy opening and closing of the card holder is another feature. (See Photograph (2).)
Housing
sApplications
Portable terminals and equipment that use GSM Standard (11.11) plug-in SIM cards.
Contacts
Photograph (3)
C39
sProduct Specifications
Rating Current rating 1 A Voltage rating 100 V AC Operating temperature -30c to +80c (NOTE 1) Operating humidity range 40 to 80% Storage temperature -10c to +60c (NOTE 2) Storage humidity 40 to 70% (NOTE 2)
Item 1. Insulation resistance 2. Withstanding voltage 3. Contact resistance 4. Vibration 5. Humidity (Steady state) 6. Temperature cycle 7. Durability (Insertion/withdrawal) 8. Resistance to Soldering heat
Specification 1000M ohms min. No flashover or insulation breakdown. 40 m ohms max. No electrical discontinuity of 10 s or more Contact resistance 60 m ohms max. Insulation resistance 100 M ohms min. Contact resistance 60 m ohms max. Insulation resistance 100 M ohms min. Contact resistance of 60 m ohms max. No deformation of components affecting performance.
Conditions 100 V DC 500 V AC / 1 minute 100 mA Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 2 hours in each of the 3 directions. 96 hours at temperature of 40c and humidity of 90% to 95% Temperature: -55c: 30 min. --> 15 to 35c: 5 min. MAX --> 85c: 30 min --> 15 to 35c: 5 min. MAX) for 5 cycles 5000 cycles Reflow: At the recommended temperature profile Manual soldering: 300c for 3 seconds
Note 1: Includes temperature rise caused by current flow. Note 2: The term "storage" refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation.
sMaterials
Part Insulator Contacts Card holder Slider Material Synthetic resin Phosphor bronze Synthetic resin Synthetic resin Finish Color : Black Contact portion: Gold plating Lead portion: Solder plating Color : Black Color : Beige Remarks UL94V-0 ___ ___ UL94V-0 UL94V-0
qOrdering Information
ID1A - 6 S - 2.54 SF (21)
1 2 3 4 5 6 1 Series Name: ID1A 2 Number of contacts: 6 3 Contact type S: Socket 4 Contact pitch: 2.54 mm 5 Terminal type SF: SMT type 6 Packaging type Blank: Tray packaging (21): Embossed tape packaging
C40
sSockets
(1.39) 29.20.3
17.40.3 2.540.2 1.180.2
No.3
OPEN
No.5
LOCK
Contact No.1 2.540.2 1.360.2
L
1
Protruding portion 2.450.3 120.1
1
Amount of sliding(1.5) OPEN LOCK
5) 1. (O
0.25t0.05 0.5w0.05
(2.1)
With the card holder closed
1) (O
L
15.80.1 (21.5) SIM CARD (GSM 11.11) (5.7)
(9.09)
1
Protruding portion
(4.82)
With the card holder open
0~180
(23.15)
3
(2.9)
7.620.2
L
(1.1) (23.02) 27.20.2 (1.1)
1
2
3
When locking, slide the protruding portion of the slider after the card holder has been closed. The co-planarity at the SMT lead tip portion is 0.1 maximum. L indicates a 7.62 0.2 center line.
Part Number ID1A-6S-2.54SF ID1A-6S-2.54SF(21)
CL No. 645-0003-9 645-0003-9-21
Number of Contacts 6 6 Tray
Packaging type Embossed tape (NOTE 1)
(0.65)
L
(10) (12) 17.40.3
No.7
Number of Pieces ___ ___ 500 pieces per reel
NOTE 1: Embossed tape packaged items are sold by the reel with 500 pieces per reel.
C41
BPCB mounting pattern
1.5 Min. 15.40.1 11.50.1 1.3 Min. 1.3 Min. 4.30.1 1.5 Min. 0.40.1 5.080.05 2.450.05 1.10.1
O1.1 + 0.1
0
Pattern prohibited area
1
120.05
2.10.05
O1
15.80.05 19.70.05
.6
+0 0 .1
3.90.05 6.4 Min.
Connector mounting position
22.2 Min.
1
Shaded portions [///] indicate pattern prohibited areas.
BTemperature Profile
5 s max. 250 240c 200
Temperature(c)
200c
150
160c 150c Applicable Conditions Reflow system: IR reflow Solder type: Cream type 63 Sn/37 Pb (Flux component 9 wt%) Test board: Glass epoxy 85 x 60 x 1 mm Metal mask thickness: 0.15 mm (30 s) 60 to 90 s Preheating time 60 120 Time (Seconds) (20 to 30 s) Soldering time Conditions may change and are dependent on type and thicness of solder.
100
50 25c(60 s) 0 Start
C42
1.1 Min.
sEmbossed Carrier Tape Dimensions
40.1
240.1
+ .5 O1
.1 +0 0
1.750.1
20.15
(2.8)
(0.9)
20.20.1 40.40.1
1.5 +0.1 +0
Unreeling direction
qReel
Dimensions
1.7
+0.15 +0
440.3
(2)
3 0. 5
(44.5)
O1
(O330)
(O80)
C43
sMethod of Using the Sockets
1. Part Structure and Names
Please see Photograph (3) on C39 page.
2. Opening the Holder Cover
Press the slider and at the same time move it in the direction marked "OPEN". This action will release the lock and free the card holder.
Remove the SIM card (as shown) so that it comes out from the card holder.
3. Closing the Holder Cover
Align the slit of the SIM card with the polarity position. Polarity
Insert the SIM card to the card holder.
Close the card holder, press the slider, and at the same time move it in the direction marked "LOCK" on the card holder. A click sound will indicate that the lock has been engaged.
C44
BPrecautions for Use
1) When opening the card holder with a SIM card inserted, avoid the action of directly lifting the SIM card and releasing the lock. Doing so will cause damage to the lock structure. 2) The card holder is based on a structure that moves only in the turning direction. Avoid pulling or applying unreasonable force in other directions. 3) Do not close the card holder when the slider is protruding from the card holder. Doing so will cause damage to the lock structure. (Please refer to the photographs below.) 4) A lock that is not fully engaged will cause poor contact. 5) Do not perform hot-line insertions. (NOTE 1) NOTE 1: The term hot-line insertion means performing an insertion while the electricity is supplied.
Yes
No
The slider is protruding from the card holder.
BWashing Conditions
1) Organic Solvent Washing
Solvent IPA (Isopropyl alcohol) HCFC (Hydrochlorofluorocarbon) Normal temperature washing Heated washing
Yes Yes
Yes Yes
2) Water Type Washing
When using water type cleaning agents (e.g., terpene, and alkali saponifiers), select the cleaning agent based on the documentation issued by the various manufacturers of cleaning agents which describes the effects on metals and resins.
3) Washing Precautions
Residual flux or cleaning agent on the sockets when washing with organic solvents or water type cleaners can give rise to the deterioration of electrical performance. In this regard it is important to check whether a thorough washing has been performed.
C45

▲Up To Search▲

Price & Availability of ID1A-6S-254SF21

	To Download ID1A-6S-254SF21 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .